FAAC Gate Installation Nationwide

FAAC Gate Installation in Irvine: What to Know First

FAAC gate installation in Irvine typically runs $2,800 to $7,500 depending on the gate’s size, weight, and whether you’re automating an existing gate or hanging a new one. Most installs are completed in a single day, with a written quote agreed to before we touch a bolt. If you have a FAAC operator sitting in a box or a gate that needs hanging and wiring, call (213) 566-7552 and we’ll give you an honest number in minutes.

Call (213) 566-7552

This page is for Irvine homeowners who own a FAAC opener or swing gate setup and want it installed correctly, not just bolted on. Victor Salinas has spent the better part of three decades working on gates across Orange County, and our techs know FAAC’s quirks. As an independent FAAC service provider, we’re not tied to manufacturer sales quotas. We fix what’s fixable and tell you straight when it’s not.

How FAAC Products Fail, and How We Fix Them

• FAAC 412 and 415 operator capacitor failures. These compact operators sit in tight enclosures, and Irvine’s dry heat pushes capacitors past their rating. The symptom is a gate that hums but won’t move, or starts and stalls halfway. The fix is a capacitor swap, which we stock for the 412, 415, and the newer C720. It’s a $120 to $180 repair that saves you from buying a whole new operator.
• FAAC 750 and 770 slave-motor desynchronization. On double swing gates, the slave leaf drifts open a few degrees after each cycle. Most techs chase the limit switches. We check the encoder first. These models use a magnetic encoder that gets dusty and drops counts. Cleaning and recalibrating it usually fixes the drift without replacing a motor.
• FAAC S800H hydraulic pump seal weep with steep driveways. Irvine lots in Turtle Rock and University Park often slope upward from the street. That grade makes hydraulic operators work harder, and the S800H’s pump seals start weeping oil onto the gate track. We replace seals and pressure-test the unit rather than condemning it. It runs another five to seven years if caught early.
• FAAC B680H articulated arm wear on heavy iron gates. If your gate was built from thick steel or iron, the B680H’s articulation points take real punishment. The symptom is a rhythmic click at the start of each cycle. That’s the arm bushing wearing oval. We machine or replace the bushing and re-grease with high-temp moly, not the light factory grease that breaks down in summer heat.
• FAAC E124 control board relay failures after power surges. Irvine’s fall Santa Ana winds knock out power and bring spikes back with it. The E124’s onboard relays are the first thing to go, leaving the gate stuck open or closed with no response from the keypad. We replace the relay, not the whole board, and add a surge suppressor at the panel so it doesn’t happen again.

Our FAAC Gate Installation Process

1. 1
   We come out and look. Free site visit. We check gate weight, hinge condition, post depth, power availability, and the FAAC operator model you have. We measure everything before we quote anything.
2. 2
   We give you a written price. The number you agree to is the number you pay. No surprises, no change orders because we forgot a bracket.
3. 3
   We mount and align. Posts get set or reinforced if needed. The operator gets mounted square, not shimmed with washers and hope. The arm or piston connects true to the gate’s rotation point.
4. 4
   We pull the power properly. Conduit, weatherproof junction boxes, and a dedicated breaker. We don’t daisy-chain off your garage door opener circuit, which we see on roughly a third of Irvine installs we correct.
5. 5
   We program and tune. Speed, force, delay, safety edges, and obstacle detection get set to the gate’s actual weight and travel. We cycle it repeatedly with a wooden block test to verify the safety sensors stop the gate without crushing anything.
6. 6
   We walk the job with you. You see the gate move, the keypad work, the safety edges function. Then we hand you the 90-Day Done Right Promise in writing and leave the driveway cleaner than we found it.

What FAAC Gate Installation Costs in Irvine

What moves the price: gate weight, post condition, power distance from the panel, and whether the old operator left behind a mess we need to undo. We quote it all upfront, including the small hardware details other companies forget to mention. Call (213) 566-7552 and we’ll give you a free, written estimate.

Why Irvine Homeowners Call Ironworks Gate Co. for FAAC Work

We’ve been at this for over 42 years, and we plan to be here for another forty. That changes how we work. We’re not racing to the next job. A FAAC gate we install in Woodbridge or Northwood is one we’ll be maintaining for the next decade, and we build it that way.

Every completed job carries the 90-Day Done Right Promise: if it’s not right, we come back and make it right, no paperwork, no arguing. Our techs are background-checked, uniformed, and trained on nine gate-automation brands, including FAAC, LiftMaster, Mighty Mule, Ghost Controls, and DoorKing. When a FAAC job needs a part that’s discontinued, we know which compatible component from another brand will work without voiding your warranty. A live person answers our phones 24 hours a day, 7 days a week. That’s not a perk, it’s how a gate company should run.

FAQs